search

Avocation-systems VGA-4 Bedienungsanleitung Seite 1

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Audio Avocation-systems VGA-4 herunter. AVocation Systems VGA-4 User Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 2
  • Inhaltsverzeichnis
  • LESEZEICHEN
    • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
VGA-4 Instructions
The VGA-4 requires 9-24vdc at 100ma in continuous operation.
The startup current draw is 800ma for 50 milliseconds so your power supply must be able to supply that initial current
rush. Most wall transformer supplies are able to supply the current required. Some regulated supplies may limit the inrush
current well and may not work unless they are rated above 800ma continuous duty.
The VGA-4 has an ID code which allows up to 8 units to operate together. The unit ID code is set by the same bank
of switches as the baud rate. The following shows the switch setting for these codes. The ID code is used in both IR
commands and serial commands. Factory default is Unit ID 0.
The VGA-4 can be controlled via IR remote signals. The unit has two methods of receiving IR coommands. The IR
window will receive codes directly from a remote or through an emitter on an IR repeater system. The connection through
the terminal block allows the VGA-4 to be hardwired into the IR repeater system. The VGA-4 will operate on any repeater
system that is based on 0vdc for no IR signal and +5 to +12vdc for an active IR signal. The VGA-4 infrared commands
operate at 38KHz.
When an IR code is being received through either method, the IR conrm LED will blink
Power Connections
ID 0 ID 1 ID 2 ID 3 ID 4 ID 5 ID 6 ID 7
VGA-4 ID
The VGA-4 is capable of teaching it’s 38KHz IR control codes to most models of learning
remotes and controllers. The teaching emitter will output the code for an input selection when a
source selection button is pressed on the unit.
1 2 3 4
1 2 3 4
Teach
RS-232
IR
Confirm
IR
+VGndS+
-
VGA-4HD
Automatic/Manual
VGA Selector
Baud
ID
Auto
Term
Teaching
Emitter
Teaching IR Commands
1 2 3 4
1 2 3 4
Teach
RS-232
IR
Confirm
IR
+VGndS+
-
VGA-4HD
Automatic/Manual
VGA Selector
Baud
ID
Auto
Term
Selection Buttons
1 2 3 4
1 2 3 4
Teach
RS-232
IR
Confirm
IR
+VGndS+
-
VGA-4HD
Automatic/Manual
VGA Selector
Baud
ID
Auto
Term
+vdc
Gnd
Input 1
Input 2
Input 3
Input 4
Output
Selection
Buttons
Operating via Infrared Control
1 2 3 4
1 2 3 4
Teach
RS-232
IR
Confirm
IR
+VGndS+
-
VGA-4HD
Automatic/Manual
VGA Selector
Baud
ID
Auto
Term
Signal
Gnd
IR
Window
Seitenansicht 0
1 2

Inhaltsverzeichnis

Seite 1 - VGA-4 Instructions

VGA-4 InstructionsThe VGA-4 requires 9-24vdc at 100ma in continuous operation.The startup current draw is 800ma for 50 milliseconds so your power supp

Seite 2 - Status Command

Serial ConnectionsThe VGA-4 can be controlled via RS-232 or RS-485. The RS-232 port is the 9-pin D-Sub connector.RS-485 is connected to the - (A) and

Kommentare zu diesen Handbüchern

Keine Kommentare
  • Mariner-software Ascendo Product Works JET Belleria
  • Akasa Computergehäuse Dimplex Sanitärkeramik Honeywell Barcodeleser Gembird Kabelnetzwerktester MyKronoz Flachbildschirmzubehör
  • Acer Aspire V5-472 Daewoo DWB-180C Lenovo IdeaPad Y510p Notebook LG BD350 Electrolux EHS68210P
  • Sony KV-14LT1B Bedienungsanleitung Samsung HT-KP10 Bedienungsanleitung Varimixer W60P Bedienungsanleitung LG HT805PH Bedienungsanleitung